Tajima TMFX Electronics

For {{#if:the Tajima TMFX machine info|the Tajima TMFX machine info|other uses}}, see Tajima{{#if:|{{#if:|, [[:{{{3}}}]], {{#if:|[[:{{{4}}}]], and [[:{{{5}}}]]|and [[:{{{4}}}]]}}| and [[:{{{3}}}]]}}}}.

{{#invoke:Infobox|infobox}}

Electronics

Tajima TMFX Power Box

The Tajima TMFX machine electronics consist of the main power box, control panel and various other small boards such as head cards and joint cards.

List of boards generally found on the Tajima TMFX models:

Power Box

Shown in picture. The TMFX Power Box houses the Tajima TMFX's main power boards which include the 2 x DU-A, the S-card, and the Main card. All four boards are attached to the large heatsink chassis with screws and can be removed with T-handle 3.0mm hex keys. There is a large amount of heat sink compound normally on each board. There is an optional fan on the underside, generally on the four head and up. It is preferred that the entire power box is shipped when undergoing repairs.

DU-A

Power and control of the X/Y motors. Successor to the DU-10 XY card used in earlier Tajima DC/HC models. There are two per machine. They have front switches to turn them on and off, there are LED colors in the front (behind a shaded screen) and will be green or orange. The control panel will automatically turn off some of the cards, temporarily, in a few situations such as a floppy read command. When a warning is triggered on any of the XY board sensors it will turn the light red and not allow any commands from there. On power up, the cards remain orange until the control panel activates them.

S-Card

Power and control of the main shaft motor. This is the largest motor on the machine. This is the only card that has an optional plug in the back, which are labeled 100V and 200V. If you have 110V power then either plug works but it is not recommended to mismatch; although the 200V only slightly leeches off of the main card's ability to provide power to the rest of the system, if anything happens to the S-card then the main card will also be damaged. If you have 200V or more from your wall power, then you have no choice but to use the 200V plug; using the 100V plug with 200V wall input may damage the S-card.

Color change card

Power to the color change motor. Also reads the color change potentiometer and some solenoids.

Head card

One card per head. Detects thread break signals from the head assembly, and powers some solenoids. If one is bad, it can interfere with signals of all, including the color change card. When configuring the control panel, it also asks to pick a head card type 1 or type 2, and if the choice is wrong then all thread break signals will be wrong and erratic.

Troubleshooting and Error Messages

The Tajima TMFX machine can produce the following error messages

Tajima Error 211

Main shaft not at fixed position. Spin manually or use the ATH function.

Tajima Error 225

Stitching outside of cap frame space.

Tajima Error 281

Color change cannot reach needle position. Check for bind. Check potentiometer.

Tajima Error 291

Thread break.

Tajima Error 2B1

Tape reader error. No reader is detected.

Tajima Error 2B2

Tape reader error. Data is corrupted.

Tajima Error 2B3

Tape reader error. End code data is incorrect.

Tajima Error 2B4

Tape reader error. Data is out of order. Please reset all units.

Tajima Error 2B5

Sequin data has an error.

Tajima Error 2B6

Tape reader error. No data coming in.

Tajima Error 2B7

Please load data first.

Tajima Error 2B8

Trying to run machine while data is still loading.

Tajima Error 2B9

Memory writing error. Try erasing all memory.

Tajima Error 2BA

Memory full. Erase designs.

Tajima Error 2BB

Cannot frame back any more.

Tajima Error 2BC

No data in memory here.

Tajima Error 2C2

Incorrect option, please change.

Tajima Error 2CE

Beam sensor is tripped, make sure both mirrors are aligned.

Tajima Error 311

Main motor not spinning. Check the S-card if it is active. Check main shaft if it is bound. This error generally requires circuit board repair of the S-Card, contact PLRElectronics for repair information

Tajima Error 312

Main shaft encoder giving incorrect signal. Check connections.

Tajima Error 316

The S-card is giving an error signal. Check card.

Tajima Error 322

The X-card is giving an error signal. Check card. This error generally requires circuit board repair of the X-Card, contact PLRElectronics for repair information

Tajima Error 323

The Y-card is giving an error signal. Check card. This error generally requires circuit board repair of the Y-Card, contact PLRElectronics for repair information

Tajima Error 382

Color change motor is not moving. Check for binds. Check connections.

Tajima Error 383

The color change location is not valid for running the head. Please check or re-center.

Tajima Error 3D1

Battery error. This error generally requires circuit board repair of the Control Panel, contact PLRElectronics for repair information

Tajima Error 3D6

CPU card detects problem with main program. Reinstall.

Tajima Error B01

Floppy disk format is not correct. Is the disk bad, or the floppy drive configured correctly?

Tajima Error B02

Floppy file system is not correct. Is the disk bad, or the floppy drive configured correctly?

Tajima Error B03

Floppy is marked as read-only.

Tajima Error B04

Floppy drive says no disk is inserted. Check drive configuration.

Tajima Error BC1

No Tajima designs found.

Tajima Error BC2

Cannot overwrite same name design.

Tajima Error BC4

Floppy write failed. Re-try.

Tajima Error BC5

Floppy disk is full.

Tajima Error C01

No response to floppy drive activation signal. Check drive configuration.

Tajima Error 1B1

Stop due to frame stepping.

Tajima Error 1B2

Stop due to stop code.

Tajima Error 1B3

Stop due to end of design.

Tajima Error 1B4

Stop due to thread trim.

Tajima Error 1B5

Stop due to sequin code.

Tajima Error 1C1

Stop due to stop button.