Embroidery Troubleshooting

From Embroidery Machine WIKI
Jump to navigation Jump to search

When an embroidery machine is not running at optimal performance there are certain Embroidery Troubleshooting tips one can follow to attempt to get the embroidery machine to run properly.

Before calling your embroidery machine technician, this troubleshooting guide might be used to fix basic problems.

When an embroidery machine becomes problematic chances are its not the machine but instead more than likely operator errors, design problems, hooping problems, thread or needle issues, etc. Before mechanically doing anything to your machine, one should check for most of the common issues.

Symptoms and Resolutions

Thread Breaks

One of the most common problems encountered in daily embroidery production is a thread break. This section covers the main reasons that a thread will break and how to minimize thread breaks. The six problem areas involve: thread, needles, materials, design, mechanics and operator technique.

Tensions Test
Tensions Test
Tensions
The tensions should constantly be checked on the machine. If the tensions are off, the machine might break threads. For more information on setting the tensions, read Embroidery Machine Service Guide - Tensions

Thread

Thread is a major cause for thread breaks. Thread like food has a shelf life. When thread is exposed to the elements (air, wind, A/C, heat, cold, humidity, oily hands, etc) it rots internally eventually and becomes very brittle. There is not a specific number of days a cone of thread is good for. Thread does not necessarily have an specific expiration date. Even new wrapped thread can rot over time.

The best thread test to preform is just to try to break the thread by hand. If it breaks easy or does not make a good clean break, then the thread is probably bad. If thread is bad, its best just to discard as it is worthless and causes more problems than the cost of the spools. Bad thread will cause numerous thread breaks and can drive an operator or technician crazy.

The best advice is to buy the best thread available and not cut corners. If the spools are expensive, that cost should be passed to the customers. Spools of threads can also be unwound to many smaller spools. When doing this, its very important to unwind the thread in a uniform fashion and with a constant tension.

Needles

Needles are generally not a major cause for problems. If the needle is installed correctly with the scarf at the back and the needle eye perfectly straight then there should not be problems unless the tip of the needle is dull, or bent.

Gently Running a finger around the tip of the needle is a good way to check for burrs. If the needle seems like it has any flaws, replace it.

Material

Certain materials require special digitizing. A good digitizer should be able to digitize for any material as long as they know what material the design will be embroidered on before digitizing the design.


Design.

Mechanical.

Technique.

Needle Breaks

Needle breaks are another common issue. Here are some likely causes:

• The needle may be dull and needs to be changed. If the needle has trouble getting through the fabric, it will eventually cause the needle to break.

• Make sure the needle is inserted properly. If it is not inserted all the way into the needle bar shaft, it could come loose while sewing and break.

• Make sure the hook timing is correct. If the machine is not timed properly, the needle may hit the hook, which could cause it to break.

Bird Nesting

There are three primary causes to birdnesting: unbalanced tension, flagging, or problems with the hook assembly.

Tension problems. Check the thread path to insure the machine is threaded properly. Then sew a tension test such as an 18mm capital "I" test.

Flagging problems. Check to make sure the fabric is framed properly. It should be tight. Also, make sure there is not a significant gap between the hoop assembly and the sewing arm.

Hook assembly problems. If there is a problem with the hook assembly, look at two things. Either the hook positioning finger is mounted too close to the hook basket, or the hook basket does not allow the sewing hook to spin freely.

Skipping Stitches

Vibrations and Noise

When an embroidery machine vibrates excessively then it might mean the machines is not on a flat surface or is not properly leveled.

False Thread Breaks

Operator Error

Tools Recommended

Having the right tools is not only important for an embroidery machine technician but also for the embroidery machine operator.