Embroidery Machine Accessories

From Embroidery Machine WIKI
Jump to navigation Jump to search
Various Accessories for a single head embroidery machine
Various Accessories for a single head embroidery machine

There are several different types of Embroidery Machine Accessories. The Embroidery Machine Accessories are used for embroidering different types of garments. For example, there are accessories for embroidering on caps and there are different accessories for embroidering jacket backs.

When embroidering on different materials, it might be necessary to change the needles.

Types of Embroidery Machine Accessories

There are a lot of Embroidery Machine Accessories one might use when embroidering on different types of garments or materials.

Some of the common types of Embroidery Machine Accessories might include

Hoops
There are several different types of hoops and hoop sizes. Generally its best to use the smallest hoop available for the logo and garment. Larger hoops for small embroidery might cause distortions. Some types of hoops include Tubular Hoops, Spider Hoops, Magnetic Hoops, etc
Cap/Hat Drivers
Cap/Hat Drivers of Frames are used when embroidery on the front of a cap. To embroidery on the back of a cap, its recommended to use a tubular hoops.
Error creating thumbnail: Unable to save thumbnail to destination
Single Head Embroidery Machine Stand
Embroidery Machine Stands
Single head machines sometimes have optional Embroidery Machine Stands with a cut out in the front to allow garments to hang.

Hoops and Hooping

Embroidery hoops are clamping devices used to hold the backing and fabric in place when using the embroidery machine. Modern hoops for embroidery machines are typically made of plastic and metal. By placing the fabric in a hoop, the fabric stays in place and the hoop moves as controlled by the machine. Hooping the garment correctly is an important part of the embroidery process.

Hoop Sizes

Listed below are some common hoop sizes and their recommended usage:

4-inch or 12cm round hoops. These hoops are used for small shirt-front or jacket-front embroidery such as personalization, hemmed sleeves, shorts and more.

6-inch or 15cm round hoops. These hoops are commonly used for embroidery over shirt pockets because they allow the embroiderer to keep the bulky pocket seams inside the hoop. In other words, even when a logo or design will fit inside a four-inch hoop, the pocket area can be trooped straighter and flatter when the hoop falls outside the pocket corners. These hoops are also used for blazer crests, aprons and jackets.

8-inch or 19cm round hoops. These hoops are most commonly used as a base to hold a spider or distancing insert for quick-change hooping systems. In this system, the hoop that holds the garment is snapped into (not screwed into) the spider which holds it

Selecting the Appropriate Hoop

Select the smallest hoop possible. Use the smallest hoop possible (that fits the design) in order to ensure that tension is even across the fabric. Make sure to leave at least a half-inch (1.27cm) on all sides of the design. This will enable good design registration.

Select the right shape. Most hoops are round or oval so this is not usually a problem. The rounded shape provides for more even tension on the fabric.

Use hoop of an appropriate material. Most hoops are made of plastic so this is not a major concern. Some are made of wood and there are some cap frames and specialty hoops that are made of metal. Special hoops made of wood called Double-Height hoops are used to hold heavy or slippery fabrics.

Types of Hoops

Tubular. This type of hoop is used when the machine table is dropped. Tubular hoops snap into a tubular sash and allow the fabric to flow freely. This makes it easier to embroider on finished garments.

Flat. This type of hoop is used when the machine table is in the up position. There are special framing systems that allow you to load and unload these hoops with ease. Flat hoops are typically used for unfinished garments or fabric.

Cap Frames. This type of hoop is used to embroider on caps. They are typically curved metal hoops made to hold caps in place.

Care of Hoops

Hang up hoops when not in use. If they are left flat they can become warped or get chipped.

Hold the metal bar to insert hoops. When inserting the hoops into the machine do not push the wood or plastic. Instead, hold the metal bar or brackets and insert into the machine.

Mark the hoop. This way you can always keep the top and bottom pieces together.

Guidelines for Hooping

Make sure the backing is large enough to fill the entire hoop. By hooping the entire piece of backing, you will better maintain even tension on the garment.

Smooth out the garment and backing. Do this before placing the hoop and make sure there are no folds or wrinkles in the garment once it is hooped.

Stretch the garment. Stretch the garment to how it will be worn before hooping it. If the garment stretches when it is worn, it will make the fabric around the embroidery look puckered.

Adjust the hoop before hooping. Do not tighten the screw after hooping the garment or it may cause "hoop burn" on the garment or cause the design to register poorly.

Marking the garment. Mark the garment with tailor's chalk, masking tape, straight pins or marking pens. This will help show you where the center of the design should start. If you are sewing many of the same garment you may be able to mark the first one, then use the hoop itself as a guideline for the remainder of the items to be embroidered.

Placement Guidelines

Left Chest. Center straight down from the shoulder seams 6-8" (15.2-20.3cm) and over 4-5" (10.1-12.7cm)

Shirt Pockets. Center between the seams of the pocket down from the edge

Jacket Backs. The center of the design should be about 6-9" (15.2-22.8cm) down from the collar